How do I install TP-Link Archer router to work with a Cable Modem ?

Archer C1200 , Archer C5400 , Archer A2600 , Archer AX55 , Archer C4 , Archer C5200 , Archer AX53 , Archer C5 , Archer AX10 , Archer C2 , Archer AX51 , Archer AX96 , Archer D50 , Archer C5v , Archer A2200 , Archer C6U , Archer C80 , Archer AXE95 , Archer C8 , Archer AX10000 , Archer C3150 , Archer C9 , Archer AX50 , Archer C6 , Archer C7 , Archer AX90 , Archer AX6000 , Archer CR700 , Archer C5400X , Archer C25 , Archer C24 , Archer A20 , Archer A64 , Archer C60 , Archer C2600 , Archer A1200 , Archer C21 , Archer C20 , Archer C64 , Archer AX1800 , Archer AX206 , Archer C59 , Archer C58 , Archer AX4200 , Archer C3200 , Archer C900 , Archer A2 , Archer AX75 , Archer AX4400 , Archer C3000 , Archer AX73 , Archer C50
Recent updates may have expanded access to feature(s) discussed in this FAQ. Visit your product's support page, select the correct hardware version for your device, and check either the Datasheet or the firmware section for the latest improvements added to your product. Please note that product availability varies by region, and certain models may not be available in your region.
Before you start, you can refer to the Video first:
Advanced Preparations:
1.Unplug your modem, and remove the backup battery if it has one.
2.Connect the powered-off modem to the router’s Internet port with an Ethernet cable.
3.Power on the modem, and then wait about 2 minutes for it to restart.
4. Connect the power adapter to the router and turn it on.
5. Connect your computer to the router.
6. Check for the LEDs to confirm the hardware connection, then refer to the following step to setup
Note: If the 2.4 GHz LED and 5 GHz LED are off, press and hold the WPS/Wi-Fi button on the back for more than 2 seconds. Both the LEDs should turn solid.
Or you can refer to the Quick Installation Guide in the packet to connect the hardware.
Note: Please make sure you are able to access the internet with a direct connection from the main computer to your cable modem. If the direct connection doesn’t work, please contact your Internet Service Provider.
Here takes Archer C7_V5 as a demonstration.
Step 1
Log in to the router’s web-based interface, to get some help, please refer to the article How do I log into the web-based Utility (Management Page) of TP-Link wireless router?
Step 2
Configure WAN Connection Type
Select Dynamic IP as the Internet Connection Type on the right of the web page, shown as below. Then click Save button.
Step 3
Wait for a few minutes and check the Internet part on the Status page, if it shows any IP address (similar as below), that means the connection between the Router and the Modem is established. If there is no IP address, please move to step 4.
Step 4
If there is still no IP address, please do the following:
1. Restart the router first, wait for about 10 seconds, and connect your end device like a computer, laptop to the router.
2. Power off the modem, and unscrew the coaxial cable
3. Power on the modem, Check LEDs on the Router, make certain the WAN/Internet LED is on.
4. Reconnect the coaxial cable to the modem and check if you can access the internet.
Note: Some cable modems have a backup battery inside. To completely restart the cable modem, please take the battery out, and then unplug the power supply.
Get to know more details of each function and configuration please go to Download Center to download the manual of your product.
Related FAQs
- How do I log into the web-based Utility (Management Page) of TP-Link wireless router?
- How do I install TP-Link router to work with a Cable Modem? (Old UI)
- How to set up an IPv6 Internet connection on the TP-Link Wi-Fi Routers
- What should I do if I cannot access the internet through Wi-Fi router?
- What should I do if I can’t log into web-based interface of my TP-Link device?
Ez a GY.I.K. hasznos volt?
Véleménye segíti az oldal fejlesztését
What’s your concern with this article?
- Dissatisfied with product
- Too Complicated
- Confusing Title
- Does not apply to me
- Too Vague
- Other
Thank you
We appreciate your feedback.
Click here to contact TP-Link technical support.
Ez a weboldal cookie -kat használ a weboldal navigációjának javítása, az online tevékenységek elemzése és a felhasználók számára a legjobb élmény biztosítása érdekében. A cookie -k használata ellen bármikor tiltakozhat. További információt az adatvédelmi irányelveinkben talál.
Ez a weboldal cookie -kat használ a weboldal navigációjának javítása, az online tevékenységek elemzése és a felhasználók számára a legjobb élmény biztosítása érdekében. A cookie -k használata ellen bármikor tiltakozhat. További információt az adatvédelmi irányelveinkben talál.
Alap Cookie-k
Ezek a cookie -k a webhely működéséhez szükségesek, és nem tilthatók le a rendszereiben.
TP-Link
accepted_local_switcher, tp_privacy_base, tp_privacy_marketing, tp_smb-select-product_scence, tp_smb-select-product_scenceSimple, tp_smb-select-product_userChoice, tp_smb-select-product_userChoiceSimple, tp_smb-select-product_userInfo, tp_smb-select-product_userInfoSimple, tp_top-banner, tp_popup-bottom, tp_popup-center, tp_popup-right-middle, tp_popup-right-bottom, tp_productCategoryType
Live-Chat
__livechat, __lc2_cid, __lc2_cst, __lc_cid, __lc_cst, CASID
Youtube
id, VISITOR_INFO1_LIVE, LOGIN_INFO, SIDCC, SAPISID, APISID, SSID, SID, YSC, __Secure-1PSID, __Secure-1PAPISID, __Secure-1PSIDCC, __Secure-3PSID, __Secure-3PAPISID, __Secure-3PSIDCC, 1P_JAR, AEC, NID, OTZ
Marketing és Elemző Cookie-k
Az elemző cookie -k lehetővé teszik számunkra, hogy elemezzük weboldalunkon végzett tevékenységeit, hogy javítsuk és módosítsuk webhelyünk működését.
Hirdetési partnereink a weboldalunkon keresztül marketing cookie -kat állíthatnak be annak érdekében, hogy érdeklődési körének profilját, és hogy releváns hirdetéseket jelenítsen meg más webhelyeken.
Google Analytics & Google Tag Manager
_gid, _ga_<container-id>, _ga, _gat_gtag_<container-id>
Google Ads & DoubleClick
test_cookie, _gcl_au
Meta Pixel
_fbp
Crazy Egg
cebsp_, _ce.s, _ce.clock_data, _ce.clock_event, cebs
lidc, AnalyticsSyncHistory, UserMatchHistory, bcookie, li_sugr, ln_or